Tubes; Suitable for Pinch valve Series PI07; Nominal diameter 25, 32mm; Material NBR lebensmittelecht

Tubes; Suitable for Pinch valve Series PI07; Nominal diameter 40, 50mm; Material NBR lebensmittelecht

Seal kit; Suitable for Series SE01, SE02, SE03; Body Brass, Bronze; Seal EPDM; Nominal diameter 25mm; Diameter Actuator 50mm; Function NC

Penstock valve; 1200x1200; Body; Stem extension And Gate Stainless steel AISI316; Seal EPDM; Handwheel; Sealed on all sides (4); Flow direction One-sided; Maximum pressure 2,6 mwc; Mounting bridge Stainless steel AISI316; 2600mm Distance between the lowest point of the pressure pipeline and the operating deck; 900mm Distance from the maneuvering deck to the bridge

BUW4-050-DSTS-S22-A
Butterfly valve with pneumatic actuator Series BUW4-DSTS-S22-A; ATEX II 2 G/D Ex h; Wafer type; Length According to EN558−1R20; Body Ductile iron EN-GJS-400-15 Epoxy coated; Disc And Shaft 1.4408; Liner PTFE/Silicone; Nominal flange pressure PN10/16/ANSI150; Single acting actuator ATEX II 2 G/D c T6; Control pressure 5,5...8bar; Medium temperature -10...+190°C; Pressure range 0...10bar; DN 50mm; Length 43mm; Actuator PAS1005
ABS54-PI08
Mounted pilot valve; Speed control; Suitable for Pneumatically operated butterfly valve; Standard coil C001; Connector size 22mm; 5/2-way solenoid valve - NAMUR type (NM52W1S-PR); Actuator PAD/PAS052-270; Hose connection Push-in fitting 8mm
MS-2P-052230-PF002
Mounted inductive dual proximity switch; 8,2VDC; 2 NC-Namur-EExi; Electric connection M12, 4-pin; P&F-NCN3-F31-N4-V1; For actuator 52 To 230

Pneumatically operated seat valve; NC; Body Stainless steel 1.4408; Seal PTFE; Butt weld ends According to DIN11850-2; For liquids; Closing against flow; Medium temperature -30...+200°C; DN 32mm; Operating pressure 0...12,5bar; Control pressure 3,5...10bar; Diameter Actuator 81mm; Head end gasket Klinger Top-chem-2000; Splash water protection

Butterfly valve with electrical actuator; Wafer type; Length According to EN558−1R20; Body Ductile iron EN-GJS-400-15 Epoxy coated; Disc 1.4408; Shaft 1.4016; Liner EPDM; Nominal flange pressure PN10/16/ANSI150; Medium temperature -10...+130°C; Pressure range 0...10bar; DN 80mm; Length 46mm; Operating time 9s; Voltage 24VAC/DC; Metal; VB060M-0E9-Q14

Butterfly valve with electrical actuator Series BUW6-DSE-02; Wafer type; Length According to EN558−1R20; Body Ductile iron EN-GJS-400-15 Epoxy coated; Disc 1.4408; Shaft 1.4016; Liner EPDM; Nominal flange pressure PN10/16/ANSI150; Medium temperature -10...+130°C; Pressure range 0...10bar; DN 100mm; Length 52mm; Operating time 27s; Voltage 24VAC/DC; Metal; VB110M-0E27-Q17

Angle seat-Control valve; G1"; DN25; Material Stainless steel 1.4408; Seal PTFE; Kvs-value 14 (100%); Characteristic linear; With mounted digital positioner 4-wire; Control signal 0-10V; Safety position: NO Spring opened

Inspection certificate EN-10204-3.1; For material

Inspection certificate EN-10204-3.1; For material

Inspection certificate EN-10204-3.1; For material

5-fold-Valve manifold Consists of 5 Pieces CSE01-12-15-AT; NC; Body Aluminum; Seals PTFE/FKM; Female thread; Pressure range 0...16bar; Medium temperature -20...+120°C; Back pressure tight; Bi-directional flow; G 1/2"; DN 15mm; Control pressure 3...8bar

5-fold-Module block Consists of 5 Pieces CSE01-12-15-AT; NC; Body Aluminum; Seals PTFE/FKM; Female thread; Pressure range 0...16bar; Medium temperature -20...+120°C; Back pressure tight; Bi-directional flow; G 1/2"; DN 15mm; Control pressure 3...8bar; Material Module: Aluminum

knife gate valve with double acting actuator series A1N; wafer type; body cast iron EN-GJL-250/ductile iron EN-GJS-500-7; gate AISI 304; soft sealed EPDM; packing PTFE-synthetic/EPDM; screws stainless steel; nominal flange pressure PN10; unidirectional sealed; control pressure 5,5...8bar; medium temperature -5...+90°C; DN 150mm; length 60mm; pressure range 0…4bar; incl. ADR-approval

Packing PTFE-Synthetic/FKM; Suitable for Knife gate valve Series A; DN 150mm

Knife gate valve with handwheel Series A1V; Wafer type; Rising stem; Body Cast iron EN-GJL-250/Ductile iron EN-GJS-500-7; Gate 1.4301; Soft sealed EPDM; Packing PTFE-Synthetic/EPDM; Screws Stainless steel; Nominal flange pressure PN10; Unidirectional sealed; Medium temperature -5...+90°C; DN 100mm; Length 50mm; Pressure range 0...10bar; Incl. Inspection certificate EN-10204-3.1; For pressure, function and tightness

knife gate valve with electric actuator series A5EB2I3-5V; wafer type; rising stem; body AISI 316; gate AISI 316; soft sealed FKM; packing PTFE-synthetic/FKM; flange ANSI150; unidirectional sealed; voltage 230V/50Hz; medium temperature -5...+90°C; DN 200mm; length 60mm; pressure range 0…7bar; actuator AUMA SA07.6

knife gate valve with electric actuator series A5EB2I3-5V; wafer type; rising stem; body cast iron EN-GJL-250/ductile iron EN-GJS-500-7; gate AISI 304; soft sealed FKM; packing PTFE-synthetic/FKM; flange ANSI150; unidirectional sealed; voltage 230V/50Hz; medium temperature -5...+90°C; DN 200mm; length 60mm; pressure range 0…7bar; actuator AUMA SA07.6

knife gate valve with double acting actuator series A1N; wafer type; body AISI 316; gate AISI 316; soft sealed EPDM; packing PTFE-synthetic/EPDM; nominal flange pressure PN10; unidirectional sealed; control pressure 5,5...8bar; medium temperature -5...+90°C; DN 100mm; length 50mm; pressure range 0…10bar